Photocatalytic degradation of methylene blue under visible light by cobalt ferrite nanoparticles/graphene quantum dots

• Vo Chau Ngoc Anh,
• Le Thi Thanh Nhi,
• Le Thi Kim Dung,
• Dang Thi Ngoc Hoa,
• Nguyen Truong Son,
• Nguyen Thi Thao Uyen,
• Nguyen Ngoc Uyen Thu,
• Le Van Thanh Son,
• Le Trung Hieu,
• Tran Ngoc Tuyen and
• Dinh Quang Khieu

Beilstein J. Nanotechnol. 2024, 15, 475–489, doi:10.3762/bjnano.15.43

• hydrothermal method was reported [7]. The effect of oleylamine concentration on the physicochemical properties of CF synthesized via a solvothermal process has been presented [8]. However, ferrites exhibit self-agglomeration due to their magnetic nature. Combining different functional materials to prepare

• this study, we describe an eco-friendly facile hydrothermal method to prepare magnetic CF/GQDs nanocomposites. The CF nanoparticles, 8–10 nm in diameter, were highly dispersed in a graphene quantum dot matrix and directly formed at 200 °C. Stacking GQDs sheets onto the CF nanoparticles resulted in CF

A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• photodetector based on CuO nanoparticles (CuO NPs) and ZnO nanorods (ZnO NRs). CuO NPs were loaded onto ZnO NRs by a cost-effective, simple hydrothermal method at low synthesis temperature [38]. The CuO/ZnO photodetector was characterized, and its sensitivity was evaluated regarding visible-light wavelengths

• process of the ZnO NRs was presented in a previous paper [63]. At the beginning, ZnO NPs (5% dispersion in ethanol) were spin-coated onto cleaned glass substrates at 3000 rpm for 30 s. Then, the sample was heat-treated at 90 °C. ZnO NRs were grown by a hydrothermal method from Zn(NO3)2·6H2O and HMTA (1:1

Carboxylic acids and light interact to affect nanoceria stability and dissolution in acidic aqueous environments

• Matthew L. Hancock,
• Eric A. Grulke and
• Robert A. Yokel

Beilstein J. Nanotechnol. 2023, 14, 762–780, doi:10.3762/bjnano.14.63

• , ACS grade, 7697-37-2; and sodium azide, Sigma, 99.8%, 26628-22-8. Lacey carbon, 300 mesh, copper grids (product #01895) from Ted Pella, Inc. were used for electron microscopy. Methods Hexagonal nanoceria particles (4.2 ± 1.2 nm) (mean ± SD) were synthesized using a hydrothermal method [55] and

A graphene quantum dots–glassy carbon electrode-based electrochemical sensor for monitoring malathion

• Sanju Tanwar,
• Aditi Sharma and
• Dhirendra Mathur

Beilstein J. Nanotechnol. 2023, 14, 701–710, doi:10.3762/bjnano.14.56

• malathion detection (Figure 10). Conclusion Graphene quantum dots (size range 5 to 40 nm) were chemically synthesized by using glucose as a precursor in a hydrothermal method. This paper describes the fabrication of an electrochemical nanosensor by modifying a bare glassy carbon electrode with GQDs. The

A TiO₂@MWCNTs nanocomposite photoanode for solar-driven water splitting

• Anh Quynh Huu Le,
• Ngoc Nhu Thi Nguyen,
• Hai Duy Tran,
• Van-Huy Nguyen and
• Le-Hai Tran

Beilstein J. Nanotechnol. 2022, 13, 1520–1530, doi:10.3762/bjnano.13.125

• evolution of 450 µmol·h−1. Reddy et al. loaded TiO2 particles on MWCNTs via a simple hydrothermal method [13]. However, the MWNTs/TiO2 nanocomposite showed photoactivity only under UV irradiation due to the high bandgap of 3.1 eV. To the best of our knowledge, there are only a few studies on TiO2@MWCNTs

Near-infrared photoactive Ag-Zn-Ga-S-Se quantum dots for high-performance quantum dot-sensitized solar cells

• Roopakala Kottayi,
• Ilangovan Veerappan and
• Ramadasse Sittaramane

Beilstein J. Nanotechnol. 2022, 13, 1337–1344, doi:10.3762/bjnano.13.110

• [2][19][20]. Hence, in this work Cu2S was chosen as the CE material. The CE was fabricated as described in [8]. At first, Cu2S NPs were prepared by a hydrothermal method using ʟ-cysteine and copper(II) chloride. Then the Cu2S paste containing 95% of Cu2S and 5% of PVdF in NMP was coated onto FTO

Recent trends in Bi-based nanomaterials: challenges, fabrication, enhancement techniques, and environmental applications

• Vishal Dutta,
• Ankush Chauhan,
• Ritesh Verma,
• C. Gopalkrishnan and
• Van-Huy Nguyen

Beilstein J. Nanotechnol. 2022, 13, 1316–1336, doi:10.3762/bjnano.13.109

• . It has been shown that the hydrothermal method of fabricating Bi-based semiconductor photocatalysts offers some significant benefits. Nanostructured materials have several advantages, including a more adaptable area for more detailed reconstruction, confinement effects, superior mechanical stability

• surface of Bi2WO6. The hydrothermal method was used, and it was discovered that the produced CuS/Bi2WO6 semiconductor photocatalyst had increased photocatalytic performance for the breakdown of glyphosate when exposed to visible light. Enhanced photocatalytic activity, excellent recyclability, high

Recent advances in green carbon dots (2015–2022): synthesis, metal ion sensing, and biological applications

• Aisha Kanwal,
• Naheed Bibi,
• Sajjad Hyder,
• Arif Muhammad,
• Hao Ren,
• Jiangtao Liu and
• Zhongli Lei

Beilstein J. Nanotechnol. 2022, 13, 1068–1107, doi:10.3762/bjnano.13.93

• quantum yield is provided in Table 1. Liu et al. used grass as a natural carbon source for the first time to prepare CDs [55]. Bhamore and co-workers reported fluorescent CDs without any surface-passivating agent by using a green precursor Pyrus pyrifolia fruit through a simple hydrothermal method at 180

• obtained by Vasimalai et al. using various spices, such as cinnamon, red chili, turmeric, and black pepper, for a simple hydrothermal method. They found that black pepper yields CDs with the highest QY up to 43.6% [62]. Vandarkuzhali et al. also obtained a very high quantum yield of 48% using pseudo-stem

• resulting in different selectivity. CDs-A and CDs-B were utilized to detect ClO− and Hg2+ in tap water and river water, respectively. Using cotton linters as a green source, water-dispersed fluorescent CDs were reported, obtained through a microwave-assisted hydrothermal method. This method provides CDs for

Sodium doping in brookite TiO₂ enhances its photocatalytic activity

• Boxiang Zhuang,
• Honglong Shi,
• Honglei Zhang and
• Zeqian Zhang

Beilstein J. Nanotechnol. 2022, 13, 599–609, doi:10.3762/bjnano.13.52

• behavior. This report shows that sodium can be doped in brookite TiO2 by the conventional hydrothermal method, meaning that other alkali anions are also expected to form the brookite AxTi1−xO2 (A = Na, K, Ca). We suggest giving more attention to the local atomic structure and the chemical composition of

Zinc oxide nanostructures for fluorescence and Raman signal enhancement: a review

• Ioana Marica,
• Fran Nekvapil,
• Maria Ștefan,
• Cosmin Farcău and
• Alexandra Falamaș

Beilstein J. Nanotechnol. 2022, 13, 472–490, doi:10.3762/bjnano.13.40

• include hydrothermal method [42], controlled wet chemistry using spin coating, which can deposit, for example, uniform Ag NPs onto ZnO nanowhiskers and nanocolumns [43], photochemical deposition, which allows the formation of different Au shapes depending on the type of additive added into the

Tin dioxide nanomaterial-based photocatalysts for nitrogen oxide oxidation: a review

• Viet Van Pham,
• Hong-Huy Tran,
• Thao Kim Truong and
• Thi Minh Cao

Beilstein J. Nanotechnol. 2022, 13, 96–113, doi:10.3762/bjnano.13.7

• , nanobelts, and nanotubes. These morphologies can be controllably obtained by using polyvinylpyrrolidone (PVP), sodium dodecyl sulfonate (SDS), cetyl trimethyl ammonium bromide (CTAB), or tetrapropyl ammonium bromide (TPAB) as surfactants in a hydrothermal method [56][57][58][59]. The difference of

• , Z. “Adsorption and oxidation of NO on various SnO2(110) surfaces: A density functional theory study”, pages 717–722, Copyright (2015), with permission from Elsevier. This content is not subject to CC BY 4.0. SEM images of SnO2 microspheres synthesized by a hydrothermal method at 180 °C for 24 h

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• hydrothermal method to synthesize reduced graphene oxide and pine dendritic BiVO4 composite with an average length of 1–1.5 μm and about 0.6 μm width [82]. In the hybrid composite rGO nanosheets were draped with a pine dendritic morphology. Figure 20 shows the SEM images of GO (Figure 20a), rGO (Figure 20b

• ppm TEA at 35% RH. Cadmium sulfide-based fractals Highly oriented CdS dendrite (HOCSD) sensors synthesized by a hydrothermal method to detect formic acid (HCOOH) and hydrazine (N2H4) were reported by Guo and co-workers [83]. The multichannel branches of dendritic structure of the CdS sensor allowed

• 2–3 µm length) by a hydrothermal method and calcined the fabricated nanostructure precursors in air [84]. Figure 23a–f shows SEM and TEM micrographs with selected-area electron diffraction (SAED) patterns of the Co3O4 nanostructures. Hydrogen peroxide (H2O2) was detected by an electrochemical sensor

9.1% efficient zinc oxide/silicon solar cells on a 50 μm thick Si absorber

• Rafal Pietruszka,
• Bartlomiej S. Witkowski,
• Monika Ozga,
• Katarzyna Gwozdz,
• Ewa Placzek-Popko and
• Marek Godlewski

Beilstein J. Nanotechnol. 2021, 12, 766–774, doi:10.3762/bjnano.12.60

• % for planar structures, respectively. The work, therefore, describes an environmentally friendly technology for PV architecture with surface textures increasing the efficiency of PV cells. Keywords: atomic layer deposition; hydrothermal method; photovoltaics; silicon; solar cell; zinc oxide

• (ZnONR) were grown via a hydrothermal method (HT) to create a rough surface morphology. Sample B was placed into the ALD growth chamber without modification of the surface morphology. During HT growth, sample B was kept under nitrogen atmosphere. After the HT process, both samples were transferred to the

• Figure 1. Results and Discussion Figure 2 shows as-grown zinc oxide nanorods on the silicon surface grown by the hydrothermal method described above. Scanning electron microscopy (SEM) images revealed that the shape of the nanorods is hexagonal. The estimated width of hexagonal rods equals 160 ± 5 nm and

The preparation temperature influences the physicochemical nature and activity of nanoceria

• Robert A. Yokel,
• Wendel Wohlleben,
• Johannes Georg Keller,
• Matthew L. Hancock,
• Jason M. Unrine,
• D. Allan Butterfield and
• Eric A. Grulke

Beilstein J. Nanotechnol. 2021, 12, 525–540, doi:10.3762/bjnano.12.43

• Research Centre Institute for Health and Consumer Protection repository of reference materials from the OECD sponsorship program. The solvothermally synthesized nanoceria material was prepared using a hydrothermal method [34]. Briefly, 0.25 M cerium chloride heptahydrate and 0.25 M citric acid monohydrate

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• increased capacitance of 226 F·g−1 at 1 A·g-1 [22]. Xia et al. used a Ti3C2Tx MXene electrode decorated with nickel oxide (NiO) nanosheets. The electrode was synthesized via a hydrothermal method. The electrode used in a supercapacitor showed an excellent specific capacitance of 80 F·g−1 and an energy

Unravelling the interfacial interaction in mesoporous SiO₂@nickel phyllosilicate/TiO₂ core–shell nanostructures for photocatalytic activity

• Bridget K. Mutuma,
• Xiluva Mathebula,
• Isaac Nongwe,
• Bonakele P. Mtolo,
• Boitumelo J. Matsoso,
• Rudolph Erasmus,
• Zikhona Tetana and
• Neil J. Coville

Beilstein J. Nanotechnol. 2020, 11, 1834–1846, doi:10.3762/bjnano.11.165

• phyllosilicate can be obtained either by a hydrothermal method or a deposition-precipitation method, the 2:1 nickel phyllosilicate is only formed under hydrothermal conditions [32][33][34]. Recently, several researchers have reported on the generation of nickel phyllosilicate catalysts for hydrogenation

Self-standing heterostructured NiC_x-NiFe-NC/biochar as a highly efficient cathode for lithium–oxygen batteries

• Shengyu Jing,
• Xu Gong,
• Shan Ji,
• Linhui Jia,
• Bruno G. Pollet,
• Sheng Yan and
• Huagen Liang

Beilstein J. Nanotechnol. 2020, 11, 1809–1821, doi:10.3762/bjnano.11.163

• [26]. For instance, molybdenum/tungsten carbide with a well-defined nanostructure was synthesized via a hydrothermal method, and the obtained metal carbide catalyst yielded a high capacity in lithium–oxygen batteries [15]. Also, titanium carbide was synthesized by Bruce et al. as cathode material for

A self-powered, flexible ultra-thin Si/ZnO nanowire photodetector as full-spectrum optical sensor and pyroelectric nanogenerator

• Liang Chen,
• Jianqi Dong,
• Miao He and
• Xingfu Wang

Beilstein J. Nanotechnol. 2020, 11, 1623–1630, doi:10.3762/bjnano.11.145

• deposited onto 45 μm p-Si by radio frequency (RF) magnetron sputtering. Next, the sample was placed into a solution of 0.877 g hexamethylenetetramine, 1.372 g Zn(CH3COO)2, and 13 mL ammonium hydroxide to grow ZnO NWs for half an hour via a hydrothermal method in a mechanical convection oven at 90 °C

High-responsivity hybrid α-Ag₂S/Si photodetector prepared by pulsed laser ablation in liquid

• Raid A. Ismail,
• Hanan A. Rawdhan and
• Duha S. Ahmed

Beilstein J. Nanotechnol. 2020, 11, 1596–1607, doi:10.3762/bjnano.11.142

• bromide (CTAB) surfactant-assisted hydrothermal method [15]. Zhang et al. synthesized monodisperse Ag2S NPs using thermolysis of harmless silver xanthates as a single-source molecular precursor and controlled the particle size by changing the alkyl chain length in the precursors [16]. Recently, Kang et al

Antimicrobial metal-based nanoparticles: a review on their synthesis, types and antimicrobial action

• Matías Guerrero Correa,
• Fernanda B. Martínez,
• Cristian Patiño Vidal,
• Camilo Streitt,
• Juan Escrig and
• Carol Lopez de Dicastillo

Beilstein J. Nanotechnol. 2020, 11, 1450–1469, doi:10.3762/bjnano.11.129

• , chemical vapor deposition, electrochemical anodization method, hydrolysis, hydrothermal method, precipitation–hydrothermal method, reverse micellar route, sol–gel method, solution-based synthesis, solvothermal synthesis, and the sonochemical method. The most relevant ones, along with the typical resulting

Gas sorption porosimetry for the evaluation of hard carbons as anodes for Li- and Na-ion batteries

• Yuko Matsukawa,
• Fabian Linsenmann,
• Maximilian A. Plass,
• George Hasegawa,
• Katsuro Hayashi and
• Tim-Patrick Fellinger

Beilstein J. Nanotechnol. 2020, 11, 1217–1229, doi:10.3762/bjnano.11.106

• formation and reversible alkali metal storage. Experimental Material synthesis Preparation of carbons derived from ᴅ-fructose The carbons synthesized via hydrothermal method were produced by a step synthesis similar to the reported preparation according to Väli et al. [30] and Fellinger and co-workers [32

• precursor overnight at 70 °C under vacuum, it was carbonized in a tube furnace with argon flow at a rate of higher than 0.5 L min−1 at 1000 °C for 1, 5, or 10 h. The carbons produced by this hydrothermal method (HT carbons) will be called HTx, where x is an integer. The synthesis conditions (temperature of

Influence of the magnetic nanoparticle coating on the magnetic relaxation time

• Mihaela Osaci and
• Matteo Cacciola

Beilstein J. Nanotechnol. 2020, 11, 1207–1216, doi:10.3762/bjnano.11.105

• additional step in which the hydrothermal method or thermal decomposition technique are used. The method used to obtain nanoparticles by thermal decomposition of an iron precursor in the presence of NaBH4 in a polyol was found to be suitable for size control in both chemical approaches [1][2][3][4][6]. Since

Gram-scale synthesis of splat-shaped Ag–TiO₂ nanocomposites for enhanced antimicrobial properties

• Mohammad Jaber,
• Asim Mushtaq,
• Kebiao Zhang,
• Jindan Wu,
• Dandan Luo,
• Zihan Yi,
• M. Zubair Iqbal and
• Xiangdong Kong

Beilstein J. Nanotechnol. 2020, 11, 1119–1125, doi:10.3762/bjnano.11.96

• activity of the as-prepared nanocomposites was investigated against Gram-positive S. aureus and Gram-negative E. coli. Experimental Synthesis of the Ag–TiO2 nanocomposite A hydrothermal method was used to prepare the Ag–TiO2 nanocomposite on a gram-scale. 1.25 mol/L of a 16.0 mL titanium sulfate solution

• addition to Ag and TiO2, indicating that the formation of the Ag–TiO2 nanocomposite was comparable to previously reported studies. The synthesis of the TiO2 and Ag–TiO2 nanocomposites using the polyvinylpyrrolidone (PVP)-assisted hydrothermal method is illustrated in Scheme 1. In the growth process, the

• on the Ag concentration in the Ag–TiO2 nanocomposites. These results proved that nanocomposites have a better antibacterial performance than the single NPs. Conclusion In this work we have designed and synthesized splat-shaped Ag–TiO2 nanocomposites (NCs) by using a simple hydrothermal method with

Effect of Ag loading position on the photocatalytic performance of TiO₂ nanocolumn arrays

• Jinghan Xu,
• Yanqi Liu and
• Yan Zhao

Beilstein J. Nanotechnol. 2020, 11, 717–728, doi:10.3762/bjnano.11.59

• of the 1D TiO2–Ag nanostructures prepared to date are Ag-nanoparticle-coated TiO2 (ACT), in which the catalytic efficiency of the catalyst is greatly decreased when the Ag loading is increased to a certain extent. Wang et al. [29] used the hydrothermal method to prepare an array of TiO2 nanocolumns

Preparation, characterization and photocatalytic performance of heterostructured CuO–ZnO-loaded composite nanofiber membranes

• Wei Fang,
• Liang Yu and
• Lan Xu

Beilstein J. Nanotechnol. 2020, 11, 631–650, doi:10.3762/bjnano.11.50

• a hydrothermal method. The effects of growth solution concentration as well as temperature and time of the hydrothermal synthesis on the morphology of the heterostructured CuO–ZnO-loaded CNFMs were investigated by SEM. Also, structure and wetting properties of the CNFMs were studied. Effect of the